What temperature should Navien tankless water heater?

120°F
O With the Navien Water Heaters, the temperature has been preset at the factory to 120°F (NR, NR-A), 140°F (NP, NP-A). The PCB board will electronically control this temperature. The output hot water temperature can be adjusted either manually using the main PCB board’s dip switches or with the remote controller.

What temperature should navien be set at?

This Navien Combination boiler is factory set at 120°F (49°C) for your safety and comfort. Increasing the set temperature increases the risk of accidental scalding.

What is the highest temperature a tankless water heater?

For your safety, Rinnai tankless water heaters come with a maximum temperature default setting of 120℉ to help prevent scalding. However, by following these simple steps, you can increase the temperature to 140℉ if you choose. Flow the six (6) step process to adjust your temperature: 1.

Does navien have a pilot light?

This appliance does not have a pilot. It is equipped with an ignition device which automatically lights the burner. BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

How do I turn up the temperature on my navien 240a?

Press the + (Up) or – (Down) buttons until the desired temperature appears on the display. You can adjust the temperature while the display is flashing. Once the display stops flashing, the temperature setting is stored.

How do you clear navien error codes?

Navien error code E016 means the heat exchanger is overheating. To fix and troubleshoot Navien error code E016, switch the unit off for 30 seconds and then back on. Check and clean the cold water filter and strainer, and flush the heat exchanger.

Is 150 too hot for water heater?

The recommended setting for household water heaters is not 150 degrees, but slightly less _ 140 degrees. Water temperatures higher than 140 degrees can burn the skin and are particularly dangerous for young children and the elderly. People with poor circulation can scald themselves without knowing it.

Do you have to light a pilot on a tankless water heater?

Tankless Gas. A tankless water heater has a lot of moving parts, and there are more things which can break then on a tank water heater. Most of these water heaters do NOT have a standing pilot light. They use electronic ignition to light the gas.

Is there a pilot light on tankless water heater?

Tankless water heaters can avoid the standby heat losses associated with storage water heaters. In a gas-fired storage water heater, the pilot light heats the water in the tank so the energy isn’t wasted. The cost of operating a pilot light in a tankless water heater varies from model to model.

Is the navien npe-240s a good water heater?

The Navien NPE-240S’s energy factor is superior to both traditional water heaters and noncondensing tankless models. Reduced vent temperatures due to this condensing technology allow you to use PVC venting, which saves you money and contributes to the ease of installation.

What is the heat capacity of the NPE 240A?

NPE-240A; Heat Capacity (input) Natural gas: 19,900 – 199,900 BTU/H (5.831 – 58.571 kWh) Propane: 19,900 – 199,900 BTU/H (5.831 – 58.571 kWh) Efficiency ratings: UEF (NG & LP) 0.96: Flow rate (DHW) 35°F temp rise: 11.2 GPM (42.4 l/m) 45°F temp rise: 8.7 GPM (32.9 l/m) 67°F temp rise: 5.6 GPM (21.2 l/m) Dimensions

How to install a navien tankless water heater?

The NaviLink module attaches easily to any new or existing* Navien NPE Series tankless water heater, NCB-E Series combi‐boiler and NHB Series boiler. Simply easy to install…same day. Simply more profitable.

Is the navien navilink module compatible with NHB boiler?

NaviLink makes it easy to communicate with your Navien systems anywhere internet service is accessible. The NaviLink module attaches easily to any new or existing* Navien NPE Series tankless water heater, NCB-E Series combi‐boiler and NHB Series boiler.