What tool is used to trim Christmas trees?

Pruning shears (or pruners, clippers or secateurs) These are probably the most-used tool when it comes to pruning shrubs, flowers, vines, and small growth on trees. Pruning shears are hand-held and can cut branches and twigs up to ¾ of an inch thick.

How do I stop my child touching the Christmas tree?

Additional ways to keep kids away from the tree

1. Skip the tree and decorate other areas of the house.
2. Put up a segmented baby gate or play yard.
3. Create a gift fence.
4. Put the tree on a table.
5. Use kid-friendly ornaments and let ’em at it.
6. Give them an alternative.
7. Final thoughts.

How do Christmas tree farms trim trees?

In essence, shearing the tree is accomplished by visualizing an imaginary cone over the tree and cutting off all the branches that stick out beyond the cone. Once shearing has been started, it must be done every year to maintain uniform density.

Is it OK to cut the top of a Christmas tree?

Topping spoils a pine tree’s natural shape. Cutting the top off a pine tree (​Pinus​ spp.) won’t immediately kill the tree, but a large pruning wound could leave the tree open to potentially deadly infections. Canopies of pine trees and many other evergreens grow outward from the needle-bearing tips of branches.

Can I cut my Christmas tree shorter?

You will be able to trim off some height from the trunk of a Christmas tree, but don’t plan on dramatically shortening a tall tree to make it fit in your home. It may be too difficult or impossible to saw off a large portion of the tree.

Are Christmas trees safe for toddlers?

For toddlers, a tree is dangerous for a few different reasons: It’s full of choking hazards. Broken ornaments can cause cuts.

Are Christmas trees poisonous to babies?

* Poinsettia and Christmas trees – Poinsettia plants and Christmas tree needles are not poisonous if eaten, but may cause mouth/throat irritation, stomach upset, or irritate the skin if handled by children. Choking on tree needles is the main concern. Tip: Do not let children play with gift wrappings.

How do you shape a growing Christmas tree?

To prune your Christmas tree, remove any upward growing stems that compete with the leader, and trim back any wayward shoots to maintain a nice even shape all round. Any dead or damaged shoots should also be removed.

How do you keep a Christmas tree from getting taller?

Once when the tree is dormant in the winter and again during the height of the summer. If you have access to commercial herbicides then you can consider applying a plant growth regulator either as a foliar spray or as a granular application to the soil surrounding the trunk.

Should you drill a hole in Christmas tree?

When a tree is first cut, air gets into the plant tissue and interrupts the tree’s ability to absorb water, says Dungey. It also makes it harder for the tree stand to hold the tree. And no matter what Uncle Joe told you, never drill a hole in the base of the trunk thinking it will help the tree draw up more water.

How tall does a Christmas tree have to be to be sheared?

Shearing is usually started when trees are 4 to 5 feet high on spruce and fir and at 3 feet on pines. Shearing and shaping can be done with hand clippers or shears or a specially-designed, long-bladed shearing knife.

How big should the base of a Christmas tree be?

Pruning and Shearing Christmas Trees [fact sheet] Pruning and shearing produce the symmetrical, high-density, cone-shaped characteristics of a quality Christmas tree. The base of the live crown of the tree should be about two-thirds as wide as the height of the tree. An 8-foot tree should have a base width of about 5 feet.

What happens when you trim a Christmas tree?

Deformities in individual trees can usually be corrected by clipping and shearing, thereby improving the quality and saleability of the tree. For example, if a tree is lopsided, it can be brought back into balance by clipping the longest lateral branches on the heavy side of the tree.

How big should a Christmas tree leader be cut?

In terminal leader pruning, the leader is cut back to the desired length, usually 8 to 12 inches. The cut should be made at an angle. It should be about 1 inch above a good bud.